Commercial R-panel (PBR) metal roofs installed and replaced across Greater Houston, from $6.00 per square foot installed. Written quote in 24 to 48 hours.
R-panel is the ribbed, screw-down steel panel on most warehouses, shops and pre-engineered metal buildings around Houston. Each sheet covers 36 inches, with raised ribs every 12 inches and the screws left visible on top. The roof version is usually sold as PBR (purlin bearing rib): its edge has a short leg that rests on the purlin under the overlap and supports the seam while it is screwed down.
RISE Roofing installs R-panel roofing in Houston on new buildings that another builder has framed, and replaces it on existing buildings. We do the roof only; we don't erect the building.

An R-panel roof can carry three warranties: the panel maker's paint warranty, a corrosion warranty on the steel, and our own workmanship warranty. The paint and steel warranties come from the panel maker, and their terms vary by maker, paint and color. Here is what current published warranties from three major panel makers say about the two paints we install:
| Paint warranty | PVDF (Kynar 500) | SMP |
|---|---|---|
| No cracking, flaking or peeling | 40โ45 years | 45 years |
| Chalking on a roof | 30โ35 years, no worse than No. 8 | 30 years, no worse than No. 6 |
| Fading on a roof | 30โ35 years, within 5 color units | 30 years, within 7 color units |
| Price | About 10โ15% more | Lower-cost paint |
On the chalk scale, 10 means no chalk at all, so a No. 8 limit allows less chalking than No. 6. For fading, fewer color units means less change. That tighter limit on a roof is the main reason to pay more for PVDF. Sources: Metal Sales PVDF warranty (45/35/35 years), McElroy Metal's Kynar 500 warranty (40/30/30 years) and MBCI Signature 200 SMP warranty.
Some makers also warrant the coated steel against rusting through. Metal Sales, for example, warrants the Galvalume steel under its PVDF paint for 50 years, and its acrylic-coated bare Galvalume panels for 45 years, against rupture or perforation from normal weather.
Because terms differ by maker and color, read the panel maker's warranty for your exact panels before you sign.
R-panel is the wrong pick when the owner or an HOA doesn't want visible screws, or for a roof you never want to think about again. That's where standing seam comes in.
Our R-panel roofing Houston prices run $6.00 to $9.00 per square foot, installed. Here is what that means at common building sizes:
| Roof size | Typical building | Installed price |
|---|---|---|
| 1,200 sq ft | Shop or garage | $7,200โ$10,800 |
| 5,000 sq ft | Small warehouse | $30,000โ$45,000 |
Where a job lands in that range depends on the gauge and paint you pick, tearing off the old roof, insulation, and how much trim and how many openings (vents, skylights, HVAC curbs) the roof has. For comparison, our commercial re-roofs in other systems usually run $7.50 to $15 per square foot.
Most roofs can be priced from a phone call; some need a site visit. Your written quote arrives within 24 to 48 hours, proposals are typically valid for 15 days, and the price is locked once you sign. For a rough number first, try our commercial roof cost calculator.
On a re-roof we tear the old panels off instead of screwing new metal over them. With the roof open we can check the purlins and framing, flag anything that needs repair before the new panels go on, and add insulation.
Standard colors typically take 1 to 2 weeks; special-order colors can take up to 4 weeks.
If the panels are still sound and the trouble is leaking screws and surface rust, a roof coating can cost much less than new metal. We are a GAF certified coating contractor and apply GAF coatings on metal roofs, typically for $2.50 to $4 per square foot, backed by a GAF Emerald Pledge warranty of 10 to 20 years depending on coating thickness. GAF requires an adhesion test before it issues that warranty, a one-time $1,500 cost. See commercial roof coating.
Many Houston warehouses have very little slope. The International Building Code (section 1507.4.2) sets the minimum for lapped metal panels like R-panel: a 3:12 slope when the side laps have no sealant, and as low as 1/2:12 when sealant is applied in the laps. Below 3:12, the code calls for sealant in the laps, and the panel maker's installation instructions set the details.
Inside the City of Houston, a commercial roof needs a Commercial Roofing Permit, which covers a new roof or an overlay on a commercial building. The city lists plan review and an inspection for it and a processing time of 10 business days, and the permit has to stay on site until final approval. We handle the permit paperwork, for the city and for county jobs outside city limits.
Most of the Houston area is outside the Texas windstorm area. In Harris County, the Texas Department of Insurance's designated catastrophe area covers only the parts of La Porte, Seabrook, Shoreacres, Morgan's Point and Pasadena that are east of State Highway 146 and inside those cities' limits (TDI's Harris County page). The coastal counties next door, Galveston, Brazoria and Chambers, are inside it county-wide, so a building on the Brazoria County side of Pearland is in it and one on the Harris County side is not.
In the windstorm area, a building needs a WPI-8 certificate from TDI to be insured through TWIA (TDI windstorm inspections). The roof has to be installed to the fastening schedule of a TDI-evaluated panel, which can mean closer purlins or more screws than an inland job. We handle the windstorm paperwork on those jobs. More on the rules: Texas windstorm insurance (TWIA).
An R-panel roof lasts about 30 to 40 years. Its weak spot is the screws: each one seals with a rubber washer, and Houston's heat wears those washers down over the years. Our advice is to have the roof walked and the screws checked around year 12, and sooner after any leak. Screws that have backed out or washers that have cracked get replaced, usually with the next screw size up. We don't sell a maintenance plan for screw-down roofs; this is simply what we recommend.
R-panel costs less up front and goes on quickly over open purlins. Standing seam hides its fasteners under the seams, lasts 50 to 70 years and needs no screw checks, but costs more. For a warehouse, shop or barn, R-panel is usually the better value. For an office, a storefront, or a roof you'd rather never think about, look at standing seam. Our commercial metal roofing page covers all the metal systems we install.
We install R-panel roofing Houston-wide, including Katy, Cypress, Spring, The Woodlands, Sugar Land, Pearland, Pasadena and La Porte, and in Waller County (Hempstead, Waller and Brookshire).
They share the same 36-inch coverage and rib pattern. PBR adds a purlin bearing leg at the overlap, which rests on the purlin and supports the seam. PBR is the usual roof panel, so check that every quote you compare names the same panel.
We install R-panel at $6.00 to $9.00 per square foot, so a 5,000 sq ft warehouse runs about $30,000 to $45,000. Gauge, paint, tear-off, insulation and the amount of trim set where a job lands.
Under the International Building Code (section 1507.4.2), lapped metal panels need a 3:12 slope without lap sealant and can go as low as 1/2:12 with sealant applied in the laps.
No. We tear the old roof off first, which lets us check the purlins and framing and add insulation before the new panels go on.
Only in the Texas Department of Insurance's windstorm area. In Harris County that is the parts of La Porte, Seabrook, Shoreacres, Morgan's Point and Pasadena east of State Highway 146; Galveston, Brazoria and Chambers counties are in it county-wide. There, a building needs a WPI-8 certificate to be insured through TWIA, and we handle that paperwork. The rest of Houston doesn't need one.
Up to three. The panel maker's paint warranty runs 40 to 45 years against peeling for PVDF (Kynar 500), with 30 to 35 years on chalk and fade, and up to 45 years for SMP, with 30 years on chalk and fade under looser limits. Some makers add a corrosion warranty on the steel, and we add a 10-year workmanship warranty on the installation. The maker's warranties cover materials, not labor.
About 30 to 40 years. Have the screws checked around year 12, and sooner after any leak.
Learn more about metal roofing standards from the Metal Roofing Alliance.
No waiting around for multiple contractors to come bid your roof. One quick call is all it takes.
Pick any slot that works for you โ online and instant.
Free video or voice call. We answer your questions and gather what we need.
We email your price-locked quote โ no pressure, no sales visit.
๐ Free, no-obligation quote โ Price-locked estimate in 24โ48 hrs
Trace your roof on satellite imagery and get a real installed price in under 60 seconds.
Powered by satellite roof measurement technology. No obligation.